Make sure to set up the receiver to use the digital audio from the input you connect to. If you're turning a computer into a music machine, why not just do the obvious: I wanna play audio from my pc to avr and shut the tv off, and then windows/avr/music software freaks out and drops the audio within 10 seconds because i shut the damn tv off. Keeping older audio gear in service. Position one speaker on each side of the computer monitor.
I wanna play audio from my pc to avr and shut the tv off, and then windows/avr/music software freaks out and drops the audio within 10 seconds because i shut the damn tv off.
The ability to connect a surround sound receiver to a computer will depend on the available connections on the computer. Hey guys, i have an onboard sound card on my pc (the 3 colored 3.5mm jacks and a yellow rca style female output on it), and i would like to connect my pc through my av receiver to my tv (av receiver being connected to 5.1 surround sound). On the receiver, plug one end of the cable to the input labeled digital. It's very easy to get this wrong. Is the receiver set to the correct output? Do not use the phono input on the receiver for this connection.; We recommend a 3.5mm mini phone plug to rca jack adapter with a rca jack stereo cable which plugs into the line or mic input of your computer's sound card. Keeping older audio gear in service. There are a few things to check: If you get no sound… don't panic. Sure, with some receivers, you can just plug and play, but for. Rca cables are widely used to connect devices like vcrs and dvd players to tv sets or cd players to stereo receivers. The dac plugs into your computer's usb port, and has analog output (often rca stereo output) for your receiver.
Both are better than analog (the red and white cables). Connect the audio cable to the green speaker out port on the back of the computer. All sound cards are made with at least one line out jack, used to power computer speakers. Select the input on the tv that corresponds to the label next to where you connected the hdmi cable from the game system. Rca cables are widely used to connect devices like vcrs and dvd players to tv sets or cd players to stereo receivers.
Ugreen 3.5mm to 2rca male cable audio.
Position one speaker on each side of the computer monitor. The ability to connect a surround sound receiver to a computer will depend on the available connections on the computer. I wanna play audio from my pc to avr and shut the tv off, and then windows/avr/music software freaks out and drops the audio within 10 seconds because i shut the damn tv off. Look for the cd input on the receiver. Both are better than analog (the red and white cables). The dac plugs into your computer's usb port, and has analog output (often rca stereo output) for your receiver. It's very easy to get this wrong. The jack is normally a 3.5mm mini phone plug. This sends digital audio to the receiver, but you can also use it if you're playing video from the computer. Hello all, i have a question about connecting pc audio to av receiver. For the new, high resolution audio formats, please see the audio connections section. Hey guys, i have an onboard sound card on my pc (the 3 colored 3.5mm jacks and a yellow rca style female output on it), and i would like to connect my pc through my av receiver to my tv (av receiver being connected to 5.1 surround sound). There are a few things to check:
I wanna play audio from my pc to avr and shut the tv off, and then windows/avr/music software freaks out and drops the audio within 10 seconds because i shut the damn tv off. The most common and least expensive way to route music from your computer to your stereo system is to run an rca audio cable from the sound card on the computer to the stereo receiver. Connect the other end of the cable to the corresponding jacks on the a/v receiver or home theater system. Keeping older audio gear in service. Hello all, i have a question about connecting pc audio to av receiver.
Rca audio cables come in pairs with two connectors on each end, a red one for right stereo and a white (or black) connector for left stereo.
Take a minute to ensure your receiver is on the right output. If you get no sound… don't panic. Both are better than analog (the red and white cables). The two rings on the connector are for carrying right and left stereo sound. Rca audio cables come in pairs with two connectors on each end, a red one for right stereo and a white (or black) connector for left stereo. These are the cables with red and white, or sometimes red and black connectors. For example, your pc is connected to the internet and you want to redirect a youtube video from pc to tv in order to watch it on a big screen with a whole room sound. I would like to change it to digital connection, but i'm. Make sure to set up the receiver to use the digital audio from the input you connect to. These cords use light to transmit the audio signals from the audio source to the receiver, and because of this, they are not affected by any electrical interference. It's very easy to get this wrong. For the new, high resolution audio formats, please see the audio connections section. Sure, with some receivers, you can just plug and play, but for.
Computer To Receiver Audio Cable / 90 Degree Audio Cable Male To Male 3.5mm AUX Stereo Cable ... : Make sure to set up the receiver to use the digital audio from the input you connect to.. If you want to make audiotapes of your mp3s (or even streaming audio concerts) for your car's tape deck, this is probably a good idea. Fiber optic cable needed to connect your pc to your home theater receiver using optical digital connection. The dac plugs into your computer's usb port, and has analog output (often rca stereo output) for your receiver. Make sure to set up the receiver to use the digital audio from the input you connect to. Optical audio cables are a great option for any home theater or audio system.